Squeezebox: Difference between revisions

From sheep
Jump to navigation Jump to search
Line 58: Line 58:
=== make jivelite use the touch library and the right input ===
=== make jivelite use the touch library and the right input ===


# install jivelight and restart
install jivelight and restart


# copy /opt/jivelite/bin/jivelite.sh to /mnt/mmcblk0p2/tce/jivelite.sh
copy /opt/jivelite/bin/jivelite.sh to /mnt/mmcblk0p2/tce/jivelite.sh


# edit and add after the first line the following:
edit and add after the first line the following:


export SDL_MOUSEDEV=/dev/input/event0
export SDL_MOUSEDEV=/dev/input/event0
export SDL_MOUSEDRV=TSLIB
export SDL_MOUSEDRV=TSLIB

my device the screen is off so I can't select the resolution

copy your /mnt/mmcblk0p2/tce/mydata.tgz file off the pi

(extract as root so you keep the uids into a new directory `tar -xzf ../ydata.tgz`)

create the file home/tc/.jivelite/userpath/settings/SelectSkin.lua with the contents:

settings = {skin="PiGridSkin_1024x600",}

rearchive the file `tar -czf ../mydata.tgz .`) and copy back onto the pi


=== bluetooth audio input ===
=== bluetooth audio input ===

Revision as of 21:17, 29 December 2021

Setup with no display

  • Plug in the ethernet cable and pull out the power plug.
  • Do a factory reset. Point the remote at the display while pressing the ADD ("+") button. Plug in the power plug and count to 7, then release the ADD button on the remote.
  • Welcome to Squeezebox. Wait 15 seconds and it will push right by itself.
  • Language selection. Press right-arrow to select English.
  • Set up networking. Press right-arrow.
  • Choose wireless or ethernet. Press down-arrow once, then right-arrow for ethernet.
  • IP address. Press right-arrow to choose DHCP.
  • Wait 30 seconds. Press right-arrow to select your SqueezeCenter server that (hopefully) it will have found.


The timing isn't really critical. For the factory setup you have to hold the button pressed for (I'm guessing) at least 5 seconds, but if you hold it too long you end up forcing another factory reset after it reboots. The 15 seconds just means wait at least 15 seconds. DHCP negotiation usually takes only a few seconds, but I've sometimes seen it take 10-20 seconds on my network.

Factory reset, right, right, down, right, right, right.

NET-UDAP perl script for setup

wifi cards

SAMSUMG NP-R40 17-000660 Sony Vaio VGN-FS515H Internal WLAN WIFI Wireless Card Board 178901432 AR5BMB5 search for AR5BMB5 in the description

squeezebox boom problems

https://broadlyuseless.info/tech/how-to-fix-unresponsive-squeezebox-boom/

picoreplayer

build your own

Make sure you have enough power if driving a touch screen and the pi or you get nasty pops

configure the screen

Edit the config.txt in the first partition add the lines for your touch device e.g.

 hdmi_group=2
 hdmi_mode=1
 hdmi_mode=87
 hdmi_cvt 1024 600 60 6 0 0 0


device

my black dac from ebay is PCM5122 and works as the iqaudio dac+

 dtoverlay=iqaudio-dacplus

calibrate touch screen

not required if you change the input type to TSLIB see below

/usr/local/bin/ts_calibrate

make jivelite use the touch library and the right input

install jivelight and restart

copy /opt/jivelite/bin/jivelite.sh to /mnt/mmcblk0p2/tce/jivelite.sh

edit and add after the first line the following:

   export SDL_MOUSEDEV=/dev/input/event0
   export SDL_MOUSEDRV=TSLIB

my device the screen is off so I can't select the resolution

copy your /mnt/mmcblk0p2/tce/mydata.tgz file off the pi

(extract as root so you keep the uids into a new directory `tar -xzf ../ydata.tgz`)

create the file home/tc/.jivelite/userpath/settings/SelectSkin.lua with the contents:

 settings = {skin="PiGridSkin_1024x600",}

rearchive the file `tar -czf ../mydata.tgz .`) and copy back onto the pi

bluetooth audio input

now supported by the UI but you need to use 5gz wifi